Fleck 5600 Valve Manual

Model 5600SXT Downflow Service Manual section of the electronic timer service manual. Position the valve to backwash. Ensure the drain line flow remains steady for 10 minutes or until the water P0.7 Fleck 3/4” Paddle Wheel Meter

Installing the Fleck 5600 Meter Control Valve: • Using the included silicone lubricant packet, lubricate the inner and outer o-rings on the bottom of the Fleck 5600 Meter Valve as shown in Figures 5 & 6

4 Model 5600 & 5600 Econominder® General Residential Installation Check List Water Pressure A minimum of 25 lbs of water pressure is required for regeneration valve to operate effectively.

MODEL 5600 & 5600 ECONOMINDER® Service Manual. MODEL 5600 Control Valve Drive Assembly (See opposite page for parts list) Printed in U.S.A. Page 5 MODEL 5600 Control Valve Drive Assembly Parts List Item No. Quantity Part No. Description

Page 4 Installation Instructions 5600/56SXT/6700 Upflow WATER PRESSURE: A minimum of 20 psi (1.4 bar) of water pressure is required for regeneration valve to operate effectively.

Fleck 5600 Econominder Installation Guide Before you assemble your new system, be sure that the following First plug in your 5600 econdominder Valve to a nearby outlet. Set the time of day, by pushing the regeneration button in,

Fleck 5600 Troubleshooting Manual Softener Product Manuals. Fleck, 5600, piston, valve, repair, filter, black, white, manual, cycles, times, how long, each cycle, brine rinse, time, by hand, High Water in Brine Tank – Problems and Solutions

Programming the Fleck 5600SXT Meter Valve: • Before start-up a few simple steps must be followed to program the Fleck indicates Valve Type 5600 Mode) Do not change this value, and press the “Extra Cycle Button” once to continue.

This instructional manual is intended to aid you in the installation and programming of your secure the upper media screen to the bottom of the water softener valve. The upper media Fleck 5600 SXT USA V1.1 – Pages Copy for Print

Programming your Fleck 5600 or 2510SXT Metered Valve • Please follow these simple steps to program the Fleck SXT Metered Valve. • You will need to know what your water’s Hardness and Iron levels are, to properly

Fleck 5600-SXT Softener Installation & Startup Guide Page 2 cleanwaterstore.com Rev 072514 Packing List All models will come with: Quantity Description

Fleck 5600SXT Downflow Service Manual 42684 Rev G JE11 TABLE OF CONTENTS 61400-12 ..Valve Body Assy, 5600, Downflow, w/TOT O-ring 1 ..19700-10 ..Valve Body, 5600, Downflow 1 Mode. After reconfiguring the system, step the valve through a manual regeneration.

Fleck 5600 Softener Installation & Startup Guide Page 2 cleanwaterstore.com Rev 031714 Packing List All models will come with:

Programming your 5600 EC valve Note: Your water treatment equipment will only comes with a service manual, showing you the valve details. Please do not follow the information in that manual, it is written with the

MODEL 5600SE Upflow – V2.0 This display is used to set the type of valve used with the control. This option setting is identified by the letter o in the first digit. There are two possible selections with #1 being the required setting:

Model 5600SXT Downflow Service Manual IMPORTANT: Fill in Pertinent Information on Page 3 for Future Reference

Page 4 Installation Instructions 5600/56SXT/6700 Upflow WATER PRESSURE: A minimum of 20 psi (1.4 bar) of water pressure is required for regeneration valve to operate effectively.

Model 5600 Mechanical Control Valve Part No. 40730 Rev C U Back (without cover) Features • Simple mechanical design is easy to use • Two valve body designs: one for downflow regeneration

Leave a Reply

Your email address will not be published.